Presentation/Phase 6 - Revision history

S.H.O. at 18:12, 28 August 2016

2016-08-28T18:12:21Z

S.H.O. at 00:07, 2 May 2016

2016-05-02T00:07:54Z

S.H.O. at 23:07, 1 May 2016

2016-05-01T23:07:27Z

S.H.O. at 22:58, 1 May 2016

2016-05-01T22:58:18Z

S.H.O.: Created page with "{{DISPLAYTITLE:Presentation → Phase 6}} thumb '''In Phase 6…'''
• First on the list is to get a square t..."

2016-05-01T22:47:10Z

Created page with "{{DISPLAYTITLE:Presentation → Phase 6}} thumb '''In Phase 6…''' • First on the list is to get a square t..."

New page

{{DISPLAYTITLE:Presentation → Phase 6}}
[[File:Let's Build the S.H.O. Drive! - Slide 145 of 176.png|thumb]]
'''In Phase 6…''' • First on the list is to get a square tote that will be used to enclose the S.H.O. Drive inside. • Second is to secure plastic spools together and secure them in the center-bottom of the square tote. • Third is to insert protective edge trim on the handles. • Fourth is to run an enclosed extended duration test.

==Inserting the S.H.O. Drive==

[[#top|(Top)]]
{{Gallery
|width=240
|align=center
|lines=14
|footer=
|Let's Build the S.H.O. Drive! - Slide 146 of 176.png||'''Square Tote''' ''(Phase 6 Parts)'' • In order to enclose the S.H.O. drive for the following test, I will use a Square Storage Box from The Container Store.
|Let's Build the S.H.O. Drive! - Slide 147 of 176.png||'''Plastic Spools''' ''(Phase 6 Parts)'' • To better secure the Supreme Stacking Crate from IRIS USA inside the Square Storage Box, I will use the two plastic winding spools (from Phase 3) so I can elevate the crate closer to the lid of the box.
|Let's Build the S.H.O. Drive! - Slide 148 of 176.png||'''Protective Edge Trim''' ''(Parts)'' • In order to secure the spools together and to center the crate against the indentions on the lid of the box, I will use U Shape Car Door Edge Guard Trim from CarBeyondStore at Amazon.com
}}

==Enclosure test==

[[#top|(Top)]]
{{Gallery
|width=240
|align=center
|lines=14
|footer=
|Let's Build the S.H.O. Drive! - Slide 149 of 176.png||'''Analog Thermometers''' ''(Measuring Devices)'' • To measure the temperature inside and outside the tote during its operation, I purchased a 12-Pack of Sper Scientific 739520 Wall Thermometers from Sper Scientific via Amazon.com
|Let's Build the S.H.O. Drive! - Slide 150 of 176.png||'''Temperature''' ''(Pre-run Testing)'' • Before I run the device, I will apply some masking tape on each thermometer and write on each the location that each will be placed during the test. • I will then place the thermometers near each other, and away from the windows, for a couple of minutes. Then I will compare their readings.
|Let's Build the S.H.O. Drive! - Slide 151 of 176.png||'''Temperature''' ''(Continuous Testing)'' • During the continuous testing, I will record their temperature periodically on camera without moving them. • To minimize data noise. I will keep the heater off and the windows and blinds closed. Preferably, clouds would be overcast during this period, or else I could choose to instead conduct the test overnight. • I will put a thermometer wherever window blinds are missing.
|Let's Build the S.H.O. Drive! - Slide 152 of 176.png||'''Temperature''' ''(Post-run Testing)'' • After the test run, these thermometers will be brought together once again away from the windows to show again for a couple of minutes to see if they give the same reading.
}}

{{Presentation Explorer}}
{{Site map}}

@@ Line 1: / Line 1: @@
-{{DISPLAYTITLE:Presentation → Phase 6}}
+{{DISPLAYTITLE:April 2016 Presentation → Phase 6}}
 [[File:Let's Build the S.H.O. Drive! - Slide 145 of 176.png|thumb|<div style="float: right">Slide 145 of 176</div>]]
 '''In Phase 6…'''<br>• First on the list is to get a square tote that will be used to enclose the S.H.O. Drive inside.<br>• Second is to secure plastic spools together and secure them in the center-bottom of the square tote.<br>• Third is to insert protective edge trim on the handles.<br>• Fourth is to run an enclosed extended duration test.

← Older revision		Revision as of 00:07, 2 May 2016
Line 32:		Line 32:
	{{Presentation Explorer}}		{{Presentation Explorer}}
	{{Site map}}		{{Site map}}
		+
		+	[[Category:Presentation]]

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Presentation → Phase 6}}
-[[File:Let's Build the S.H.O. Drive! - Slide 145 of 176.png|thumb|Slide 145 of 176]]
+[[File:Let's Build the S.H.O. Drive! - Slide 145 of 176.png|thumb|<div style="float: right">Slide 145 of 176</div>]]
 '''In Phase 6…'''<br>• First on the list is to get a square tote that will be used to enclose the S.H.O. Drive inside.<br>• Second is to secure plastic spools together and secure them in the center-bottom of the square tote.<br>• Third is to insert protective edge trim on the handles.<br>• Fourth is to run an enclosed extended duration test.